We have silver braided bars with a silver content of 55% (L-Ag55) with a length of 500mm. Because of the relatively low melting point of this silver braze, the model builder in the field of technical model building is almost exclusively concerned. The working temperature of this hard solder is 630 ° C. The silver as an alloying component in the solder does not only reduce the working temperature, but also improves the flow properties. Furthermore, silver has the positive property of combining well with other metals. For brazing brass and steel, silver solder flux is essential. The low working temperature of the silver solder bars allows the thermal load to be as low as possible for the processed material. It is important not to heat the workpieces too much, especially in the case of brass. In combination with our silver solder flux you achieve with these silver solder always optimal results. The silver braided bars can be purchased from us in the shop in 2 different diameters. For fine soldering as it often happens in technical model construction we recommend the 1mm rods. The 1mm silver braided bars are easy to carry with the hand and can be easily melted with small burners. For larger parts we prefer the 1.5 mm silver solder bars. With these rods you get faster material to the soldering point if needed. What can be brazed?The following materials can be combined with silver solder: brass, copper, gunmetal, gray cast iron, rusting steels and stainless steel. A combination of the materials among each other is easily possible with this silver braze solder. If the material is not known to you, it is always recommended to solder a piece to the sample beforehand. This allows you to determine whether the materials can be combined with the silver braze.Instructions Brazing with silver solder If you have never worked on silver solder and you are not sure how the exact solder brazing procedure is with silver solder, we can help you before you buy the silver solder. We have created a guide for you in our Bengs Modellbaumagazin on the topic "Brazing with silver solder". Here you can find out what you need and have to consider if you want to solder 2 components with silver solder. Tip: Flux residues and discoloration of the material can be optimally eliminated with our satin brushes or abrasive fleece!Characteristics of the silver solder bars500 mm long. 1mm or 1.5mm diameter Silver solder bars L-Ag55 (55% silver) Working temperature 630 ° C Bengs Modellbau has used this silver solder bars for years.  

Are you looking for a gift for an enthusiastic model building enthusiast, but don't know what they need? No problem, at this point you can purchase a Bengs model building voucher. Simply select the amount you want, the amount is equal to the euro value of the voucher. Proceed to checkout and we will then send you a beautifully designed postcard-sized voucher by post. There is a voucher code on this voucher that you can use to order from us both in the online shop and by telephone.

Ready-to-use and dosing silver solder paste, 56% silver content (L-Ag55) with the working temperature 650 ° C. The silver solder paste is suitable for fine brazing. The hard solder paste is suitable for creating almost invisible soldering seams, even in inaccessible places. With our silver soldering paste, there are virtually no solder residues at the soldering point, which must be labored. No flux required. Dried silver soldering paste is made ready for use again with a few drops of water. Mix thoroughly before removing. Typical application examples for the silver soldering paste are: Apparatus and equipment for the food industry silver contacts Bronze and brass fittings Modelling piping Heat and cooling technology Fashion Jewelry glasses manufacturing Precision Engineering !!! The silver soldering paste is also suitable for kiln soldering (furnace should have a working temperature of at least 680 ° C) !!! Contents 10 g Here you will find a tutorial on how to braze with silver solder paste.

High temperature soft solder with a melting point of 250 ° C is suitable for fittings, pipelines and components on steam engines, Stirling engines and flame eaters. The soft solder is filled with a flux that burns without residue when flame brazing (flux residues must be removed in the case of piston soldering !!!). If you need additional flux, you can use normal soft solder flux. Due to the increased melting point of 250 °, it is a good alternative to brazing. However, the high-temperature softening braze can not replace brazing. This product should not be used in the vicinity of the boiler. The use of silver solder is recommended. Wire diameter: 1mm Wire length: 1000mm This product is unleashed !!!

These replacement powder containers are suitable both as a powder container for the powder coating device and for storing unneeded powder. The replacement powder containers come with a screw cap so you can store the powder in a dry place. With a replacement powder container, changing the color when powder coating with the Power Coat 4 PRO is much quicker. The replacement powder containers are made from break-resistant plastic. The standard size of the replacement powder containers can hold 0.5L of powder. This makes them suitable for most powder coating applications. Replacement powder container powder gun for Power Coat 4 PRO Contents 0.5l Height 16cm Diameter 7.5cm

When brazing, fluxes have the task of loosening and removing the oxide layers present on the soldering surfaces and preventing them from forming again during soldering. The flux is adjusted to the working temperature of our Silver hard solder matched. Before use, the flux for silver solder should be stirred well. Using the brush in the bottle, a thin layer can be applied to the component to be soldered. You can find detailed instructions in our model making magazine (Hard soldering with silver solder instructions). If the silver brazing flux has dried out, you can make it liquid again with distilled water. Brazing with silver solder rods without flux is not possible. When the flux is heated with the burner, the water it contains first evaporates. This can be seen in the final formation of small bubbles. When the component is heated further with the flux and the working temperature is reached, the flux paste begins to melt and becomes transparent. Now the moment has come where the silver solder can be added. The effective range of the flux for silver solder is between 500°C and 800°C. The flux is suitable for brazing copper, brass, gunmetal, steel and stainless steel. Tip: Flux residues and discoloration of the material can be optimally removed with our Satin brushes or remove with abrasive fleece. You can get the flux for silver solder from us in the packaging sizes: 50g. Bottle with brush 100g.Bottle without brush

The white soldering brick is ideal as a soldering base for brazing and soldering in model building. The solder seal can be cut as required. In addition, soldering and holding needles can be inserted very easily into the brick in order to fix the component to be soldered. The white tiles have a relatively smooth and plane surface, through which sharp edges several bricks can be assembled seamlessly. To fix components that are to be soldered, you can simply nail into the porous material of the soldering iron. Thus, a soldering device can be produced very quickly. The soldering bricks are also suitable for the construction of a melting point. By assembling several soldering bricks, one can produce an excellent soldering place in which the gas flame of the burner can be optimally utilized. Dimensions of the brazier: 220mm x 110mm x 30mm

Flux-Coated High-Silver Brazing Alloy For coarser soldering work in model making, crafts, or industry, we offer flux-coated silver solder rods with a diameter of 1.5mm or 2mm. These high-quality L-Ag55 solder bars contain 55% silver and have a working temperature of 630°C. The flux range is between 500°C and 800°C, eliminating the need for additional brazing flux. When brazing brass, a low working temperature is crucial. The high silver content not only reduces the required temperature but also enhances the flow properties. Additionally, silver bonds well with other metals, ensuring strong and durable joints. Versatile Applications Our flux-coated silver solder rods are ideal for brazing: Brass Copper Heavy metals Rusting steels Stainless steel All these materials can also be joined together. Thanks to the integrated flux coating, no additional flux is required. For more details, refer to our model magazine guide on brazing flux-coated silver solder rods. Product Features Diameter: 1.5mm or 2mm Length: 500mm Material: L-Ag55 silver solder (55% silver) Working temperature: 630°C Flux range: 500°C – 800°C No additional flux needed Cadmium-free (Cd-free)

The silver solder wire is suitable for particularly fine soldering points in model making, crafts, industry or jewelery trade. Silver solder wire is only 0.5mm thick and can be very finely dosed. We supply you the silver braided wire as a 5 meter long piece and you can cut the silver solder wire as desired. You can also use this silver solder wire to form rings, for example, which can be used to solder a wave around the shaft during soldering and then only have to heat it with flux. By this process the silver solder is equal in the required place. The working temperature of this hard solder is 630 ° C. The silver as an alloying component in the solder does not only reduce the working temperature but also improves the flow properties. Furthermore, silver has the positive property of combining well with other metals. Brazing flux is essential for brazing brass and steel. Tip: Flux remedies and discoloration of the material can be optimally eliminated with our Satinbrushes! The silver solder wire 0.5 mm is suitable for brazing brass, copper, heavy metals, steels and stainless steel. All materials can be joined together. 1 Packing unit includes 5m 0.5mm silver solder wire Silver solder wire L-Ag55 (55% silver) !!! Cadmium free !!!

These satin wheel are available in fine, medium and coarse grain sizes. You can use these satin wheel to clean the surface or the material you have started. Optimum cleaning of the satin wheel also brazed components but also to remove a rust or oxide layer on small components in model building, the satin brushes are suitable. The grinding wheel are fixed on the mandrel. The wheels can easily be clamped into the chuck of a fast grinder, for example Dremel or Proxxon. We use the satin wheels to clean parts soldered with silver solder. Characteristics of Satin wheel: Diameter Satining wheel: 22mm Shank: 2.35 mm Manufacturer: Scotch

Soft soldering paste for brass, copper, steel and silver steel. The paste is applied thinly to the parts to be tinned and heated with a brazing lamp. For large-area soft soldering, it is optimal to tin- the parts beforehand. For example, we use the paste to pre-tine the cylinder and the mirror when constructing a model steam engine. The tinning paste can also be used optimally as a flux substitute. The soft soldering paste is excellently suitable as corrosion protection for steel parts. Bengs Modellbau uses the zinc paste for steel cylinders with a cooling water jacket. For example in the Flammenfresser Kurfürst. Stirring the paste before use is not necessary! The soft soldering paste may be diluted with water. Ready-to-use metal paste Contents: 50g Bottle with brush Click here for the modeling magazine: Soldering with soft solder paste and tin paste Soldering and tinning with soft soldering and tinning paste

Special soldering wire for soft soldering stainless steel and steel but also non-ferrous metals such as brass and copper. Very easy to use and all metals mentioned can be combined with each other. The flux contained in the wire is characterized by high temperature resistance. Optimum wetting on a wide variety of stainless steel makes this lead-free soft solder wire a top product. The use of additional flux is usually not necessary. The soft solder remains shiny even after long-term use of the soldered workpieces and has a very good color match to stainless steel. Processing instructions for soft soldering stainless steel Heat the components to be connected with the soldering torch to approx. 250°C and feed the wire. The flux flows out of the wire and spreads to the soldering point. The solder melts and wets the material where the flux could previously work. Then let the component cool down and remove any flux residue with water. Only suitable for 1.4301, 1.4305 or similarly alloyed stainless steels. Not suitable for higher alloyed (V4A) stainless steel qualities. Technical information soft solder for stainless steel Melting range: 221 °C Working temperature: 280C° - 350C° max. Continuous operating temperature: 100°C Low temperature resistance: - 200°C suitable for soldering in the field of food technology Lead-free Wire diameter: 1.5mm Wire length: 1000mm Suitable for soldering the following base materials Stainless steel (1.4301, 1.4305) Copper Brass Bronze Steel Carbide metals and connections of the materials mentioned with one another  

The Power Coat 4 PRO is a high-quality powder coating system for small to large areas. You will receive the powder coating gun in a high-quality plastic case in which everything has its place. This powder gun is significantly more robust than our standard powder coating system. This makes it suitable for use in commercial businesses and for ambitious DIY enthusiasts. Advantages of powder coating over painting: Ready to use immediately without drying time Extremely robust and abrasion-resistant Optimal corrosion protection Environmentally friendly as no solvents Absolutely uniform surface quality Coating remains elastic e.g. for springs The Power Coat 4 PRO has a 500 ml powder container so that even larger areas can be coated with powder without having to refill the coating powder in the meantime. Another advantage of this device is that there is a water separator and a pressure regulator directly on the powder gun. This makes setting the correct pressure much easier. Scope of delivery: Powder coating device with Schuko earthing plug, stable ground clamp, water separator and pressure regulator Two 500ml powder containers to screw into the coating gun Funnel for easy filling of the powder containers Sturdy case for storage 14 pages German operating instructions The Power Coat 4 PRO powder coating device is suitable for many different powder coating applications. With this powder coating system, even the smallest components can be easily powder coated. Even larger parts are no problem thanks to the 500 ml powder container. Our powder coating systems are very often used in the restoration of old motorcycles or cars. With this system it is possible to coat entire motorcycle frames or rims with powder varnishfor coating. The result is indistinguishable from industrial powder coating. Powder coating is also very often used in technical model making because the finished surface is extremely robust, scratch-resistant and provides good corrosion protection. Application examples powder coating of vintage car parts Powder coat motorcycle parts Powder coat rims Powder coating of small parts in technical model making This powder gun is a Tribo powder coating system. The powder becomes statically charged in the barrel of the gun due to the friction on various materials. The device is connected to the earth conductor of the socket via a ground terminal and a Schuko plug, which means the component is grounded. Due to the electrostatic charge generated during the run, the coating powder adheres to the workpiece. This effect allows you to coat a variety of materials. The charging occurs when the powder particles touch the wall of the barrel of the powder gun, causing electrons to be released from the Teflon™ barrel. The powder paint particles are separated from the spray gun faster than the charge can be redistributed. This means that the powder particles remain charged and stick to any material. You do not need any additional electricity for the tribo process. The included plug is only the ground connection of the device. Power Coat 4 PRO can process all coating powders that are suitable for Tribo systems. Here in our online shop you will find suitable spare parts for the powder coating system. p> Coating wood, tiles and glass In contrast to conventional powder coating systems, this powder gun coating system can also be used to coat wood, tiles and glass. Since these materials are not conductive, the ground terminal cannot be connected here. This makes applying the powder a little more difficult. You should first make a sample to test the properties of the material and its behavior during powder coating. What else is needed (not included) Compressor Extension hose oven for burning (min. 200c ° from a small household oven to our)

Blockade® braze is a phosphorus-tin-silicon braze for soldering copper and brass with a very low working temperature (650°C). This hard solder can be used as an alternative to the significantly more expensive Ag-55 silver solder (working temperature 630°C). Blockade has good flow properties, the soldering gap fills very quickly and forms an evenly formed groove at the soldering point with a smooth surface. Blockade® brazing solder is suitable for hat soldering copper and copper alloys, such as brass, bronze, gunmetal. You will receive a flux-coated rod from us and do not need any other additives or fluxes. The flux-coated brazing rods are suitable for all flame brazing processes as well as for induction heating and oven brazing. Blockade is used in the refrigeration, air conditioning and electrical industries. We at Bengs Modellbau are now increasingly using brazing solder in our model making workshop. In order to keep shipping costs as low as possible, we cut the brazing rods into 2 equal parts. You will then receive 2 pieces from us with a length of 250 mm. For larger quantities or when sending parcels, you will receive the brazing rods in the original length of 500 mm. Properties flux coated phosphorus-tin-silicon braze blockage Diameter: 2mm  Length: 500mm Phosphor-tin-silicon alloy Working temperature: 650C° No additional flux required Cadmium-free The easiest way to remove the contamination caused by the flux after brazing with the phosphorus-tin-silicon brazing solder blockage is with our Abrasive fleece.

JB Weld is considered to be the strongest glue in the world! It was developed 30 years ago in the USA and sold millions of times. It is located in almost every household. The 2-component epoxy resin adhesive is universally applicable and creates truly durable connections. With this adhesive, metallic materials such as cast iron, gray cast iron, steel, aluminum, brass, bronze, copper and tin can be cold-welded. The all-purpose adhesive also unbreakably combines wood, glass, ceramic or plastic. J-B Weld sticks everything - permanently and super fast. The all-purpose adhesive consists of 2 components. On the one hand there is the hardener (also called activator), in the red tube, on the other hand the part called by the manufacturer as "steel" in the black tube. This is made of epoxy resin and some other components. Both components are mixed together in equal proportions, whereby the reaction process of the curing (polymerization) is initiated. After mixing the 2 components, JB Weld can be processed for 25 minutes. After 8-15 hours, the adhesive is fully cured. Now, as if it were metal, it can be painted, painted, sawn, doweled, sanded or sanded. JB Weld does not shrink and tear during the curing process. A clean adhesive tape remains clean (as with soldering or welding), a smooth surface remains smooth. This makes JB Weld ideal where high-precision work is required. In the commercials of the manufacturer it is advertised that this all-purpose glue can reliably stick cracks in engine blocks. The cured adhesive is water resistant / steam resistant, withstand temperatures up to 300 ° C, oils, acids and chemicals (even battery acid). From the hands, it can be washed with water and soap after processing. Does not smell, since without solvent. In addition, the JB world is ideally suited for filling and gluing parts that are to be coated with the EasyCoat powder coating system. Opened for 5 years! Contents: 2 x 28g Permanently joins metal, plastic, ceramics, wood, glass, masonry, etc.   Ideal for filling cavities in castings   Seals pipes and fittings   Instead of welding, soldering, doweling   Can be drilled, painted, sanded   Temperature resistant up to 300 ° C   Water resistant and steam test   Resists oils, acids and chemicals   Tensile strength: 278 kg / qcm   Suitable for filling and gluing powder coating parts

This abrasive fleece or cleaning fleece is suitable for cleaning all metallic surfaces, preparing for brazing or soldering. But even after the brazing with silver solder and flux the pads are very good for cleaning the soldering seam. You can use pads for all materials used in technical modeling, such as brass, copper, steel and aluminum. The abrasive fleece has no metallic abrasion and is therefore also very suitable for stainless steel. The cleaning fleece does not leave any marks, so that a subsequent polishing of the components is not a problem. The sanding pads are very durable and can be used very often. Bengs Modellbau uses this cleaning fleece for soldering work regardless of whether brazing or soldering.The abrasive fleece is, of course, also suitable for cutting or milled brass parts. A pack of cleaning fleece contains 10 pads in the size 130mm x 60mm (Made in Germany)

The center punch set consists of 25 center punches made of hardened steel. The center punches are suitable for transferring holes from one component to another. To do this, a centering center punch is inserted either into the hole of an existing component or into the hole of a template and transferred to the second part. The center punch set is suitable for use in mechanical engineering, steel construction, crafts and hobbies. The grain diameters increase by 0.5mm from 1mm to 13mm. The actual dimensions of the center punches are 0.05mm below standard dimensions. All 25 center punches are 120mm long. The center punches are delivered with a clear metal stand. Centering center punch set (25 pieces) from 1mm to 13mm 0.5mm increments

Refill gas 100ml lighter gas is suitable for the two CFH Gas Solderer Diamond 40 and and Gas Solderer Diamant M50. You can also use this refill gas to refill gas lighters. The amount is enough to refill the gas soldering diamond 40 approx. 10 times. Including various filling adapters. Content: 100ml Gas:14% propane, 86% butane  

This hot steam oil for model building is ideal for the operation of real steam models. The hot steam oil is very viscous and also adheres very well to hot components. When a model steam generator is operated with steam, normal oil (for example, fine mechanics oil) is washed out very quickly by the steam. Since the hot steam cylinder adheres very well, it remains in the cylinder, the piston and the piston rod for a long time. You can also use the hot steam oil in our displacement oil. Due to its viscous nature, the hot steam oil is not suitable for lubricating Stirling engines or flame eaters.

With this powder coating machine, you can easily apply powder coatings to materials such as metal, non-ferrous metals and aluminum. In addition, you can also use the powder coating system to coat non-conductive materials such as ceramic or glass powder coated. The special feature of this powder coating device is that the powder is only statically charged and no high voltage is required. This powder coating plant does not require a power connection. All you need is a compressor. With this device, you are able to produce a professional powder coating in your own workshop. A powder-coated component is significantly more robust and durable than a painted component. This powder gun is a tribo powder coating system. The powder is statically charged by friction in the course of the gun. Electrostatically charged, it adheres to the workpiece. Through this effect, you can coat a variety of materials. Charging is effected by the powder particles touching the wall of the barrel of the powder gun, thereby dissolving electrons from the Teflon ™ barrel. The separation of the powder lacquer particles from the spray gun takes place more quickly than the charge can redistribute. As a result, the powder particles remain charged and stick to any material. You do not need any additional electricity for the Tribo process. The enclosed plug is only the earth connection of the device. Includes: AlPowder coating gun with EU (Schuko) ground plug 250ml powder container Funnel for a simple loading of powder into a powder cup 14 page user guide in English with multiple pictures that will guide you through a powder coating process safely. Powder coating is the process when powdery plastic particles (usually polyester or polyuretan) are electrostatically applied to a clean metal surface using a powder coating device. The process is used throughout the industry to create a durable, professional finish. The principle is quite simple, after the preparation and the degreasing of the component, the powder is positively charged by the gun. Similar to a TV screen attracts dust, the component now attracts the charged powder cloud. In the next step, the powder-coated component is placed in an electric furnace. Please note that the oven is no longer used for food preparation. Most powders require about 15 minutes of baking at 180 ° C. The average time from the powder coating to the ready-to-install component takes about 30 minutes.  What else is needed (not included in the set) Compressor with pressure regulator extension hose Oven alternatively small pizza oven FFP2 protective mask safety goggles Well ventilated workplace Advantages of coating: Extremely robust and abrasion resistant Without drying time immediately ready for use Optimal corrosion protection Environmentally friendly as there are no solvents Absolutely uniform surface quality Elastic coating e.g. For springs

You will get powder coating powder in facade quality in 250g bottles. The coating powder is filled into plastic bottles so that the powder remains permanently dry. With the powder you can create an easy to clean, weather and UV-resistant and extremely durable surface coating. The powder is suitable both for powder coating with corona and with tribo coating devices. The coating powder has excellent light and weather resistance. It also has a good elasticity so you can even coat feathers. The powder adheres to all surfaces. All powder coatings available at our company are suitable for corona powder coating systems as well as for tribo powder coating systems.  The following coating powder colors are available: RAL 1003 Signal Yellow Glossy (250g) RAL 3000 Fire Red Glossy (250g) RAL 5005 Signal Blue Shining (250g) RAL 6020 Chromium oxide green Glossy (250g) RAL 7001 Silbergrau Shining (250g) RAL 7016 Antrazite Gray Glossy (250g) RAL 9005 Deep black Glossy (250g) RAL 9005 Deep black Deep matt (250g) RAL 9010 Pure White Glossy (250g) Transparent colorless high gloss (250g) Chrome Metallic Gloss (250g)

The Flame eater oil from Bengs Modellbau is particularly suitable for lubricating the pistons and cylinders of flame-eaters in technical model construction. The flame-eater oil is an oil, based on white oil. It is liquid as water, odorless and biodegradable. Another important advantage of our Flame-eater oil for use in technical model construction is that it does not attack paints and varnishes. When the flame eater or parts of the flame eater exceed the temperatures of 150 ° C, the flame-eater evaporates and produces a beautiful white smoke. The oil we offer is normally used in the aircraft RC model building as smoke oil.   Many oils leave behind residues in the hot vacuum engine, which cause the piston to run smoothly in the cylinder. Likewise, when lubricating with graphite powder, deposits of graphite dust are produced over time, which lead to the piston becoming dull. These residues must be removed from time to time. For a long time we asked ourselves:   Which oil is best used for a flame eater or vacuum motor? And here is finally the solution! Flame eater oil from Bengs Modellbau. With the oil from Bengs Modellbau you do not have the described disadvantages and also the following advantages:   Flame eater oil is liquid like water   Odor neutral biodegradable It does not attack lacquers Best suited for technical modeling Made in Germany No dangerous good according to UN, IMO, ADR / RID, IATA / ICAO. Contains: 100ml   E-mail of a satisfied customer: I have today the Flammenfresseröl from you for my Stirlingmotor tried. Until now, I have oiled the model engines with WD 40. But the oil of you is a show! The high speeds I got with it are not comparable with WD 40. And all without residue and no hardening. Simply super! Best regards Video Flame eater oil   

This ceramic brazing plate is ideal for all soldering work. The ceramic brazing plate is provided with 2.9mm mounting holes, so that the parts to be soldered can be fixed well on the soldering pad. The ceramic brazing plate is ideal for soldering in model construction. The soldering plate has a very flat surface on which you can align very well soldering parts. Mounting holes: Ø 2.9 mm Dimensions: 150mm x 100mm x 22mm The ceramic brazing plate is not suitable for brazing, it tends to tear in the case of irregular heating. Please use our soldering tin.

The cutting discs with electroplated diamond coating are ideal for cutting glass tubes or test tubes to bring length. If you are building a Stirling model this is essential. The diamond cutting discs fit the mandrels from Proxxon and Dremel high-speed grinders. The mandrel is not included!!! Dimensions of the diamond cutting disc Location hole: 2mm Diameter: 22mm Carrier thickness: 0.2mm Thickness of the diamond cutting disc perforated with coating: 0.5mm Thickness of the diamond cutting disc, unperforated with coating: 0.4mm Order the disc carrier with 2.35mm diameter with screw at the same time. The mandrel for the diamond cutting disc has a reinforced shaft for better concentricity.