No results were found for the filter!
This brass Ms58 hexagonal material is very easy to machine and is ideal for turning, milling, drilling and tapping. The material is suitable for self-assembly of screws, model building nuts and other components for technical modeling....
From €3.20 *
115 Cr V3 Silver steel round material is suitable for the production of shafts, piston rods or for the construction of crankshafts for steam engines and Stirling engines in model construction. The silver steel is hardenable and can thus...
From €3.10 *
Brass Ms58 flat material is a very good machinable material. Brass is probably the most widely used material in technical modeling. Which is certainly due to the fact that it can be worked very well. It can be milled, turned, drilled,...
From €14.50 *
Das weiche Kupferrohr ist für alle Anwendungen im Dampfmodellbau und für den Technischen Modellbau geeignet. Das Cu-Rohr eignet sich auch für Benzinleitung oder Dieselleitung für Motorräder, Traktoren und Oldtimer. Das Kupferrohr ist...
From €8.50 *
Square brass in different diameters. This brass is very good machinable and suitable for turning, milling, drilling and tapping. Square braces, fork heads and other components for technical modeling are very well suited to be...
From €3.90 *
Brass Ms58 is a very good machinable material. Another advantage of brass is that it is rust-free. It is suitable for turning, milling, drilling and tapping. In addition, it can be well brazed with silver brazing and soldering. These...
From €3.10 *
Brass round pipe for the construction of small boilers for steam engines. Also capacitors, steam storage, wind kettle or oiler for model steam plants, can be produced very well from this material. In addition, Bengs Modellbau uses the...
From €8.20 *
This stainless steel 1.4305 is very easy to cut and is ideal for turning, milling, drilling and tapping. This stainless steel can be used well everywhere in model construction. as a stainless piston rod for a model steam engine. However,...
From €2.80 *
This graphite round material is excellent for making pistons for flame emitters and Stirling engines. A graphite piston does not need to be lubricated since it is self-lubricating. The graphite and material can be machined as well as a...
From €7.10 *
Aluminum round material AlCuMgPb (drilling and turning quality). This aluminum is ideally suited for use in model building. It is relatively cheap, it can be easily chipped and worked, it does not rust and is very light compared to...
From €2.90 *
The hard copper tube Sf-Cu is suitable for all applications in steam model construction and for technical model construction. In contrast to the soft copper tube, this copper tube is delivered straight in the bar. If you want to install...
From €9.20 *
Round material red brass is a sliding bearing material with good emergency running characteristics. GC-Rg 7 is suitable for the production of plain bearings or for the production of pistons or cylinders for steam engines, Stirling...
From €16.30 *
The brass pipe made of Ms63 can be used for all applications in technical model construction. For example as a fuel line for combustion engines, Rehling for model ships, cooling water line for Stirling engines or steam line in steam...
From €4.80 *
This pipe is a hydraulic cylinder pipe. The inside of the tube is very dimensionally stable and wear-resistant. The cylinder tube is suitable as a cylinder sleeve for an internal combustion engine or flame eater. We also use this...
From €13.70 *
Cast iron with lamellar graphite. The surface is peeled on the gray cast iron bars. The round bars are a little over-sized. You can also make a 30mm piston with a 30mm diameter. The material is suitable both for the production of pistons...
From €21.00 *
Cast iron with lamellar graphite. The surface is peeled on the gray cast iron bars. The round bars are a little over-sized. You can also make a 30mm piston with a 30mm diameter. The material is suitable both for the production of pistons...
From €5.00 *
Viewed