This tube is a hydraulic cylinder tube. The inside of the tube is very dimensionally stable and wear-resistant. The cylinder tube is suitable as a cylinder sleeve for an internal combustion engine or flame eater. We also use this cylinder tube in our models. We use it for the combustion engine Karl,  Stirling engine "Big Laura" and the Flame Eater Jarne. Due to its high wear resistance, the tube has proven itself as a cylinder sleeve for us. Dimensions of hydraulic cylinder tube 25mm: Outer diameter: 35mm Inner diameter: 25mm Length: 83mm Material: St52 Suitable Piston rings for this cylinder tube can be found here Dimensions of hydraulic cylinder tube 30mm: Outer diameter: 40mm Inner diameter: 30mm Length: 86mm Material: St52 Dimensions of hydraulic cylinder tube 40mm: Outer diameter: 50mm Inner diameter: 40mm Length: 117mm Material: St52 Dimensions of hydraulic cylinder tube 50mm: Outer diameter: 60mm Inner diameter: 50mm Length: 142mm Material: St52

Cast iron with lamellar graphite. The surface is peeled on the gray cast iron bars. The round bars are a little over-sized. You can also make a 30mm piston with a 30mm diameter. The material is suitable both for the production of pistons or cylindrical sleeves for model-built motors as well as for the production of plain bearing bushes. We use this material for the pistons at the station "Karl". The round material can be perfectly machined on the lathe and on the milling machine and has excellent running characteristics. All round bars are 300mm long.

Brass Ms58 flat material is a very good machinable material. Brass is probably the most widely used material in technical modeling. Which is certainly due to the fact that it can be worked very well. It can be milled, turned, drilled, brazed and softened. Many Stirling engines, steam engines and flame eaters in technical model construction are mainly made of MS58 brass. You can order brass flat material in different thicknesses from 2mm to 6mm here at the Bengs Modellbau Shop. Flat Material Brass Quality: Ms 58 (drilling and turning quality) Strength F45-50 Flat material 50mm wide Length 300mm

These relatively small spark plugs are particularly suitable for model combustion engines. Its metric M10 × 1 thread also fits into smaller cylinder heads. The spark plugs fit into our internal combustion engine and can be used as a spare part. Of course, you can also use the spark plug CM-6 for your own development with our ignition components. Data of spark plug CM-6 M10x1 Key range: 14.0 mm Overall length: 36mm External thread: M10x1 Thread length: 8.6 mm

Brass Ms58 is a very good machinable material. Another advantage of brass is that it is rust-free. It is suitable for turning, milling, drilling and tapping. In addition, it can be well brazed with silver brazing and soldering. These characteristics are very much in line with the technical model builder. Most steam engines, Stirling engines and flame eaters in model making are largely made of MS58 brass. We offer you here in the Bengs Modellbau Shop brass round material in the diameter from 1mm to 50mm. Features of brass Ms58 round Round Material Brass Quality: Ms 58 (drilling and turning quality) Strength F45-50 You always get 300mm long brass Ms58 round sections. Saving set thin brass Ms 58 / You save 20% Brass round material 300mm per 1 rod 4mm 5mm 6mm 8mm 10mm 12mm 14mm 16mm Saving set thick brass Ms 58 / you save 20% Brass round material 300mm per 1 rod 18mm 20mm 22mm 30mm

This brass Ms58 hexagonal material is very easy to machine and is ideal for turning, milling, drilling and tapping. The material is suitable for self-assembly of screws, model building nuts and other components for technical modeling. You can order different key sizes in our shop, or you can order a set of different diameters. Features of brass Ms58 hexagon  Hexagonal material brass with different key ranges Quality: Ms 58 (drilling and turning quality) Strength F45-50 Length: 300mm We supply the brass Ms58 hexagon in 300mm sections. Savings set Hexagon brass Ms 58 / You save 20% The brass hexagonal material savings set includes 300mm per 1 bar 4mm 5mm 6mm 8mm 10mm 12mm

The Ignition condenser for intermittent ignition is a component which should not be missing. The condenser regulates the strength of the ignition spark. This ignition coil is also installed in the internal combustion engine Karl and can be used as a spare part. You can use this capacitor to create an ignition breaker for model building. This is a solid moped technology that has proven itself over many years. An intermittent ignition is very durable and also times a wrong polung.   Dimensions Capacitor for Ignition condenser Length: 41mm Diameter: 18mm Threaded connection: M4  

Use this Ignition interrupter to generate the spark. You can control the breaker directly via a cam or via a ram. This article is a serial product from the moped technology. This guarantees a good quality, long durability and fast availability. You can create your own ignition system from this interrupter. We also use this breaker in the ignition of our internal combustion engine "Karl". It can also be used as a spare part in this model.   Dimensions of the Ignition interrupter Length: 30mm Width: 30mm Height: 20mm

This ignition coil is suitable for installation in an intermittent ignition. This ignition coil is also installed in the internal combustion engine Karl and can be used as a spare part. In the normal case, this coil is used for ignition in mopeds. However, due to its reliability and performance, it is very well suited for model construction. An intermittent ignition usually works very reliably and can be more easily checked for faults than an electric ignition.   Dimensions of ignition coil 12V intermittent ignition Length: 123mm Diameter rear: 40 mm Largest diameter collar: 48 mm Connection thread: 2x M4

Square brass in different diameters. This brass is very good machinable and suitable for turning, milling, drilling and tapping. Square braces, fork heads and other components for technical modeling are very well suited to be manufactured from square material. Features of brass Ms58 square material Quality: Ms 58 (drilling and turning quality)Strength F45-50 We supply the brass Ms58 square material in 300mm sections. Saving set square brass Ms 58 / you save 20% The brass square material savings set contains 1 rod 300mm long 4mm 5mm 6mm 8mm 10mm

Here you will find a toggle switch with which you can start and stop the ignition of your model motor. The toggle switch is designed both mechanically and electrically robust. We also use this toggle switch for the inflammation of our internal combustion engines. Thanks to the classic design, the toggle switch fits well with the most varied model-motor.  Switching capacity 10 A / 250 V ~ 1-pole Execution ON / OFF Operating temperature -25 ... + 85 ° C Switching cycles> 10,000 Mounting Ø 12 mm screw Overall dimensions without shield (LxWxH): 29x16x53 mm

Here you can order spare parts for your stationary engine Karl. All milled parts are numbered as in the construction plan. We mill all milled parts for the combustion engine from MS58 on a CNC milling machine.  Please refer to the parts list for the Karl stationary motor for the required number of pieces. The price always refers to one piece. Spare parts milled parts stationary engine Karl Part 2 / 1 piece of side cheek right MS58 112mm x 40mm milled part Part 3 / 1 piece side cheek left MS58 112mm x 40mm milled part Part 4 / 2 pieces bearing cap crankshaft MS58 36mm x 11mm milled part Part 5 / 1 piece bearing cover camshaft MS58 21mm x 6mm milled part Part 8 / 1 piece cylinder holder MS58 56.5mm x 50mm milled part Part 13 / 1 piece rocker arm outlet MS58 35mm x 8mm milled part Part 15 / 1 piece rocker arm holder MS58 35mm x 24mm milled part Part 17 / 1 piece rear frame strut MS58 47mm x 8mm milled part Part 27 / 2 pieces of crank web MS58 50mm x 60mm milled part Part 34 / 1 piece cam outlet MS58 16mm x 4.80mm milled part Part 35 / 2 pieces of ram guide side plates MS58 35mm x 12mm milled part Part 38 / 1 piece bearing block tappet guide MS58 18mm x 10mm milled part Part 39 / 3 pieces bearing block no. 4. MS58 18mm x 9mm milled part Part 42 / 2 pieces regulator arm MS58 37mm x 10mm milled part Part 44 / 1 piece control frame MS58 41mm x 28mm milled part Part 49 / 1 piece control lever MS58 65mm x 16mm milled part Part 57a / 1 piece of gear camshaft MS58 43.88mm x 3mm milled part Part 58a / 1 piece of gear crankshaft Ms58 22.4mm x 3mm milled part Part 71 / 1 piece fuel gauge MS58 23mm x 15.5mm milled part Part 79 / 1 piece capacitor holder MS58 30mm x 30mm milled part

Machine base made of gray cast iron for the stationary engine Karl. If you need a replacement machine base for the Karl stationary engine, you can order it here in our model making shop. The machine base corresponds to the original base that is included with the material kit for the stationary motor. Dimensions of machine base stationary motor Karl Weight: 2.20kg Length: 190mm Width: 95mm Height: 60mm Material: GG25