Weichlöten
- Kolbenlöten: ist das Erwärmen der Lötstelle und das Abschmelzen des Lotes mit einem von Hand oder maschinell geführten Lötkolbens.
- Lötbadlöten: Die Verbindungspartner werden in ein Bad aus flüssigem Lot getaucht.
- Löten im Ofen (Ofenlötung): Das Lötteil wird in der gasbeheizten Ofenkammer erwärmt. Weichlot und Flussmittel werden vorher dazugegeben.
- Flammlöten: Die Erwärmung wird durch die Verbrennung eines Brenngases erzielt.
High temperature soft solder with a melting point of 250 ° C is suitable for fittings, pipelines and components on steam engines, Stirling engines and flame eaters. The soft solder is filled with a flux that burns without residue when flame brazing (flux residues must be removed in the case of piston soldering !!!). If you need additional flux, you can use normal soft solder flux. Due to the increased melting point of 250 °, it is a good alternative to brazing. However, the high-temperature softening braze can not replace brazing. This product should not be used in the vicinity of the boiler. The use of silver solder is recommended. Wire diameter: 1mm Wire length: 1000mm This product is unleashed !!!
Soft soldering paste for brass, copper, steel and silver steel. The paste is applied thinly to the parts to be tinned and heated with a brazing lamp. For large-area soft soldering, it is optimal to tin- the parts beforehand. For example, we use the paste to pre-tine the cylinder and the mirror when constructing a model steam engine. The tinning paste can also be used optimally as a flux substitute. The soft soldering paste is excellently suitable as corrosion protection for steel parts. Bengs Modellbau uses the zinc paste for steel cylinders with a cooling water jacket. For example in the Flammenfresser Kurfürst. Stirring the paste before use is not necessary! The soft soldering paste may be diluted with water. Ready-to-use metal paste Contents: 50g Bottle with brush Click here for the modeling magazine: Soldering with soft solder paste and tin paste Soldering and tinning with soft soldering and tinning paste
Content: 0.1 Kilogramm (€106.00 / 1 Kilogramm)
Special soldering wire for soft soldering stainless steel and steel but also non-ferrous metals such as brass and copper. Very easy to use and all metals mentioned can be combined with each other. The flux contained in the wire is characterized by high temperature resistance. Optimum wetting on a wide variety of stainless steel makes this lead-free soft solder wire a top product. The use of additional flux is usually not necessary. The soft solder remains shiny even after long-term use of the soldered workpieces and has a very good color match to stainless steel. Processing instructions for soft soldering stainless steel Heat the components to be connected with the soldering torch to approx. 250°C and feed the wire. The flux flows out of the wire and spreads to the soldering point. The solder melts and wets the material where the flux could previously work. Then let the component cool down and remove any flux residue with water. Only suitable for 1.4301, 1.4305 or similarly alloyed stainless steels. Not suitable for higher alloyed (V4A) stainless steel qualities. Technical information soft solder for stainless steel Melting range: 221 °C Working temperature: 280C° - 350C° max. Continuous operating temperature: 100°C Low temperature resistance: - 200°C suitable for soldering in the field of food technology Lead-free Wire diameter: 1.5mm Wire length: 1000mm Suitable for soldering the following base materials Stainless steel (1.4301, 1.4305) Copper Brass Bronze Steel Carbide metals and connections of the materials mentioned with one another
Content: 10.5 Gramm (€76.19 / 100 Gramm)