Workshop files in a roll bag. 5-piece

Thanks to their square grinding, our machine thread drills are also suitable as hand-held tap drills. You have the choice between through-hole tap drills (blind hole drills) and basic drill tap drills. The through-hole tap is suitable for through holes where the chips can fall out. Taps for through holes have a longer cut but are more stable than basic hole drill. The ground hole drills are ground with a right-hand twist, which causes the chips to be ejected upwards, which is of course an advantage for ground holes. They have a very short cut to cut the thread as far as possible into the bore and to create a thread that is as long as possible. However, it should be noted that the stiffness of the taps is significantly lower in the case of the sizes M2 and M2.5. The taps are made of HSS steel and are suitable for threading in steel, brass, plastics, copper, cast steel, aluminum and stainless steel. If you always use sufficient cutting oil during the thread cutting, the service life of the taps is considerably increased. Particularly when cutting small threads in model construction such as M2, M2,5 or M3, we recommend our round winder. This allows a safe and accurate cutting of threads with a clearly reduced risk that the tapping tool breaks. If you want to drill a core hole but do not have a table book or a thread table, this is no problem. There is a simple rule of thumb for metric control threads. Just take the diameter of the tapping tap times 0.8. Example M5 = 5mm diameter x 0.8 = 4mm core hole drill. Machine thread tap HSS With square cut (can also be used as a hand-held drill) right hand cutting industrial quality You can choose between two different thread-cutting variants, namely through-hole tap and basic drill tap. The following taps are always available: Gewindebohrer Durchgangsloch M2 Gewindebohrer Durchgangsloch M2,5 Gewindebohrer Durchgangsloch M3 Gewindebohrer Durchgangsloch M4 Gewindebohrer Durchgangsloch M5 Gewindebohrer Durchgangsloch M6 Gewindebohrer Durchgangsloch M8  Gewindebohrer Grundloch M2 Gewindebohrer Grundloch M2,5 Gewindebohrer Grundloch M3 Gewindebohrer Grundloch M4 Gewindebohrer Grundloch M5 Gewindebohrer Grundloch M6 Gewindebohrer Grundloch M8  

Autosol Chrome Shine is a world-famous and internationally awarded cleaning, care and polishing agent for all metallic surfaces. Dirt and rust can be easily removed in one operation. Thanks to the balanced formulation of the active ingredients, in addition to excellent cleaning, surface protection is applied to the metals. Achieves a brilliant high gloss. Ideal for polishing brass, copper or aluminum. Simply apply a small amount of Autosol Chrome Shine to a cloth and polish until the desired result is achieved. For round parts, simply clamp them in the lathe and polish with a cloth. Contents: 75 ml

This twist drill set consists of 49 profile-ground drill bits. The twist drills have a particularly high concentricity and pitch accuracy, as well as a precise tip grind. You can recognize profile-ground drills by their bare surface. The drill set is delivered and stored in a practical metal box. Thanks to the precise tip grinding, the drills do not run and drill round, dimensionally accurate holes. The twist drill set is not a hardware store product but rather industrial quality. Thanks to the 0.1mm gradation of the drills, you always have the right drill at hand, regardless of whether you want to make threaded holes, an undersized hole for a reamer or an oversized hole for a shaft bushing with a clearance fit. Industrial quality (not hardware store goods) You have two different drill boxes to choose from: Twist drill set from 1mm - 5.9mm drill bits 49 pieces Twist drill set of 6mm - 10mm drill bits 40 pieces Replacement Twist drill to fill the drill boxes can be found here.  

DIN 223 cutting dies for the finished, teach-based metric ISO control thread according to DIN 13. The cutting edges have a closed pre-slit form. They can either be clamped in a cutting-edge holder or in the cutting-edge holder for the Bengs model-making machine. The cutting units are made of HSS steel (high-speed working steel). They are suitable for machining brass, copper, steel, stainless steel, silver steel, plastics and cast iron. Lubrication of the cutting tool with cutting oil is absolutely recommended. It increases the service life (life) of the cutting tool and reduces the effort required to make the thread. Industiequalität High cutting performance Tolerance field 6g DIN 223B = EN 22568 The following tapping tools are always available:  M2 Schneideisen Hss / M2 / 16mm x 5mm  M2,5 Schneideisen Hss / M2,5 / 16mm x 5mm  M3 Schneideisen Hss / M3 / 20mm x 5mm  M4 Schneideisen Hss / M4 / 20mm x 5mm  M5 Schneideisen Hss / M5 / 20mm x 7mm  M6 Schneideisen Hss / M6 / 20mm x 7mm  M8 Schneideisen Hss / M8 / 25mm x 9mm  M10 Schneideisen Hss / M10 / 30mm x 11mm